Search found 2397 matches
- Yesterday, 16:31
- Forum: ElmerSolver
- Topic: Reference Norm
- Replies: 1
- Views: 16
Re: Reference Norm
You are supposed to know the reference norm when you set up a test case. Consistency testing of solvers Each solver may be tested for consistency. The way the testing is performed is that it is assumed that the correct solution will have a predefined norm. After the simulation has been carried out t...
- 25 May 2024, 22:49
- Forum: ElmerSolver
- Topic: wrong displacement values using "ElasticSolver"?
- Replies: 23
- Views: 252
Re: wrong displacement values using "ElasticSolver"?
That is correct.
- 25 May 2024, 13:09
- Forum: ElmerSolver
- Topic: wrong displacement values using "ElasticSolver"?
- Replies: 23
- Views: 252
Re: wrong displacement values using "ElasticSolver"?
I ran the 0.1x0.01x1.0 in calculix, another open source fea tool. Using non-linear geometry option. It also calculated 0.088 same as ElastcSolver
- 25 May 2024, 12:12
- Forum: ElmerSolver
- Topic: wrong displacement values using "ElasticSolver"?
- Replies: 23
- Views: 252
Re: wrong displacement values using "ElasticSolver"?
"With this definition we say that the Young's modulus is constant, regardless of stress and strains. Is this correct? Are you saying that the ElasticSolver decides by its own that beyond a certain strain the material is no longer linear? Moreover, beyond the yield strength, in typical material...
- 25 May 2024, 11:14
- Forum: ElmerSolver
- Topic: Closed coil with core simulation
- Replies: 37
- Views: 17318
Re: Closed coil with core simulation
If you run
ElmerGrid 2 2 MESH -autoclean
it will open in ElmerGUI
but it renumbers the BCs
The ElmerSolver should run with the mesh as is.
ElmerGrid 2 2 MESH -autoclean
it will open in ElmerGUI
but it renumbers the BCs
The ElmerSolver should run with the mesh as is.
- 24 May 2024, 23:55
- Forum: ElmerSolver
- Topic: wrong displacement values using "ElasticSolver"?
- Replies: 23
- Views: 252
Re: wrong displacement values using "ElasticSolver"?
I thought they were two independent bodies connected by springs, but apparently they share nodes at the boundary? That is a different problem than I thought.
- 24 May 2024, 23:05
- Forum: ElmerSolver
- Topic: wrong displacement values using "ElasticSolver"?
- Replies: 23
- Views: 252
Re: wrong displacement values using "ElasticSolver"?
I thought perhaps it was due to rigid body modes, ElasticSolve and StressSolve so not much like rigid body modes in a static solution. So I added some constraints to take out rigid body motion without impacting the results. ElasticSolve converged much faster, but still arrived at 0.0044 answer. I at...
- 24 May 2024, 16:41
- Forum: General
- Topic: B field from wire current
- Replies: 5
- Views: 78
Re: B field from wire current
I ran it and received the same error, not seen that error before floodfill is a programming function to fill an array typically by area. It must have something to do with the BCs These BCs do not throw the error Boundary Condition 1 Target Boundaries(3) = 4 5 6 Name = "cube_4_faces" AV {e}...
- 24 May 2024, 13:55
- Forum: ElmerSolver
- Topic: Non-conformal mesh contacts
- Replies: 10
- Views: 140
Re: Non-conformal mesh contacts
The whole case is here
https://github.com/mrkearden/case
https://github.com/mrkearden/case
- 24 May 2024, 13:44
- Forum: ElmerSolver
- Topic: Non-conformal mesh contacts
- Replies: 10
- Views: 140