- animate.gif (852 KiB) Viewed 1 time
Search found 2327 matches
- 14 minutes ago
- Forum: ElmerSolver
- Topic: 3D simulation of a Motor without application of a load
- Replies: 2
- Views: 29
- 42 minutes ago
- Forum: General
- Topic: Problems with the tutorial model
- Replies: 1
- Views: 4
Re: Problems with the tutorial model
Only equation 1 is being applied to the bodies Body 1 Target Bodies(1) = 1 Name = "Body Property 1" Equation = 1 Material = 1 End Body 2 Target Bodies(1) = 2 Name = "Body 2" Equation = 1 Material = 2 End However there are two equations Equation 1 Name = "MgHarm" Active ...
- Yesterday, 18:17
- Forum: ElmerSolver
- Topic: 3D simulation of a Motor without application of a load
- Replies: 2
- Views: 29
Re: 3D simulation of a Motor without application of a load
This allowed for a solution to be obtained ! stator_airgap Boundary Condition 2 Name = rotational_mortar_airgap_curve Mortar BC = 4 !Cylindrical Projector = True ! Rotational Projector = Logical True !Projector Skip Nodes = True ! Discontinuous Boundary = Logical True Level Projector Extruded Edges ...
- Yesterday, 13:53
- Forum: ElmerSolver
- Topic: Coaxial wave guide
- Replies: 1
- Views: 18
Re: Coaxial wave guide
I modified the test case to use coordinates x, y, and z.
No mag function in MATC, may consider writing a user function.
No mag function in MATC, may consider writing a user function.
- 02 May 2024, 13:29
- Forum: ElmerSolver
- Topic: Error using CoilSolver
- Replies: 20
- Views: 1490
Re: Error using CoilSolver
I changed the air mesh to a cylinder, not sure that matters. If I plot coilcurrent, which is supposed to nodal values it is 15000. If I plot coilcurrent e , which is supposed to be elemental values it is 30000.
- 01 May 2024, 20:28
- Forum: ElmerSolver
- Topic: Thermal-Stress Analysis in Elmer
- Replies: 1
- Views: 43
Re: Thermal-Stress Analysis in Elmer
Taking this case of steady state stress due to heat
viewtopic.php?t=8128
and then modifying it to read a time history from a file and do transient.
viewtopic.php?t=8128
and then modifying it to read a time history from a file and do transient.
- 01 May 2024, 12:17
- Forum: ElmerSolver
- Topic: Strange problem with MgDyn-Solver
- Replies: 8
- Views: 243
Re: Strange problem with MgDyn-Solver
I took a cylinder of the same size and meshed it in a sphere of air and a cylinder of air and the results were very different. Same element type and density.
- 30 Apr 2024, 11:39
- Forum: General
- Topic: Newbie question about electric field solving on PCB
- Replies: 1
- Views: 110
Re: Newbie question about electric field solving on PCB
You can search this forum for PCB, there have been PCB models discussed.
- 29 Apr 2024, 12:51
- Forum: ElmerSolver
- Topic: Strange problem with MgDyn-Solver
- Replies: 8
- Views: 243
Re: Strange problem with MgDyn-Solver
With your geometry it my be best to stick with a cylinder for the air with a mesh similar to Figure 14.1 on page 91
https://www.nic.funet.fi/pub/sci/physic ... orials.pdf
https://www.nic.funet.fi/pub/sci/physic ... orials.pdf
- 28 Apr 2024, 14:12
- Forum: ElmerSolver
- Topic: Strange problem with MgDyn-Solver
- Replies: 8
- Views: 243
Re: Strange problem with MgDyn-Solver
The air volume in paraview can be turned off and one by using the threshold filter, filter on geometry IDs, you can filter to only show the bodies you want to see. In the run I posted I had put voltage on the outer skin, and ground on the inner skin. I will re-run with voltage on the end. I tried me...