take a look at these cases
https://github.com/ElmerCSC/elmer-elmag
Search found 2361 matches
- 07 May 2024, 21:35
- Forum: ElmerGUI
- Topic: Model induction between two coils
- Replies: 31
- Views: 425
- 07 May 2024, 21:33
- Forum: ElmerSolver
- Topic: Steady state convergence tolerance
- Replies: 12
- Views: 465
Re: Steady state convergence tolerance
Peter is best suited to give a technically explanation but for my limited brain; strategy 1, which I associate with loose couple they converge in steps on after another linear convergence, complete till converged ==> non-linear convergence, complete till converged==> steady state convergence, repeat...
- 07 May 2024, 17:39
- Forum: ElmerSolver
- Topic: Steady state convergence tolerance
- Replies: 12
- Views: 465
Re: Steady state convergence tolerance
I would describe it as the solution to the equation/equations always vary with time, until a steady state develops. Steady state as opposed to transient gets to the steady state non-changing result faster than going through every transient step. Steady state means that the variables are no longer ch...
- 05 May 2024, 14:27
- Forum: ElmerSolver
- Topic: 3D simulation of a Motor without application of a load
- Replies: 5
- Views: 147
Re: 3D simulation of a Motor without application of a load
I was just looking through these examples
https://github.com/ElmerCSC/elmer-elmag
It will run without the Anti Rotational Projector, it is not needed.
The choice of projector I think is mainly based on geometry and solution type.
https://github.com/ElmerCSC/elmer-elmag
It will run without the Anti Rotational Projector, it is not needed.
The choice of projector I think is mainly based on geometry and solution type.
- 04 May 2024, 00:44
- Forum: ElmerSolver
- Topic: 3D simulation of a Motor without application of a load
- Replies: 5
- Views: 147
- 04 May 2024, 00:16
- Forum: General
- Topic: Problems with the tutorial model
- Replies: 1
- Views: 46
Re: Problems with the tutorial model
Only equation 1 is being applied to the bodies Body 1 Target Bodies(1) = 1 Name = "Body Property 1" Equation = 1 Material = 1 End Body 2 Target Bodies(1) = 2 Name = "Body 2" Equation = 1 Material = 2 End However there are two equations Equation 1 Name = "MgHarm" Active ...
- 03 May 2024, 18:17
- Forum: ElmerSolver
- Topic: 3D simulation of a Motor without application of a load
- Replies: 5
- Views: 147
Re: 3D simulation of a Motor without application of a load
This allowed for a solution to be obtained ! stator_airgap Boundary Condition 2 Name = rotational_mortar_airgap_curve Mortar BC = 4 !Cylindrical Projector = True ! Rotational Projector = Logical True !Projector Skip Nodes = True ! Discontinuous Boundary = Logical True Level Projector Extruded Edges ...
- 03 May 2024, 13:53
- Forum: ElmerSolver
- Topic: Coaxial wave guide
- Replies: 2
- Views: 93
Re: Coaxial wave guide
I modified the test case to use coordinates x, y, and z.
No mag function in MATC, may consider writing a user function.
No mag function in MATC, may consider writing a user function.
- 02 May 2024, 13:29
- Forum: ElmerSolver
- Topic: Error using CoilSolver
- Replies: 20
- Views: 1651
Re: Error using CoilSolver
I changed the air mesh to a cylinder, not sure that matters. If I plot coilcurrent, which is supposed to nodal values it is 15000. If I plot coilcurrent e , which is supposed to be elemental values it is 30000.
- 01 May 2024, 20:28
- Forum: ElmerSolver
- Topic: Thermal-Stress Analysis in Elmer
- Replies: 2
- Views: 115
Re: Thermal-Stress Analysis in Elmer
Taking this case of steady state stress due to heat
viewtopic.php?t=8128
and then modifying it to read a time history from a file and do transient.
viewtopic.php?t=8128
and then modifying it to read a time history from a file and do transient.